Beretta A400 Xtreme Plus Problems(With Fixes)

The Beretta A400 Xtreme Plus is well known for its superior performance and reliability, proving to be a popular choice among hunters and shooting enthusiasts. 

However, like any sophisticated piece of machinery, it is not immune to occasional issues or problems. 

This document aims to shed light on some of the most common problems encountered with the Beretta A400 Xtreme Plus, as well as their potential fixes. 

12 Common Beretta A400 Xtreme Plus Problems

While the Beretta A400 Xtreme Plus is generally revered for its versatility and performance, some users have reported a few concerns.

Primarily, the issues revolve around the break-in period, with the shotgun performing less reliably during this phase.

Furthermore, some shooters have highlighted that the Kick-Off recoil reduction system can feel a bit stiff initially. Like any firearm, proper maintenance and break-in procedures can alleviate most of these initial problems.

1 . Failure to Eject (FTE)


The Failure to Eject (FTE) problem in the Beretta A400 Xtreme Plus generally occurs due to a dirty or damaged ejector. 

The ejector, a critical component of the firearm, is responsible for removing spent shells from the chamber after firing.

 If it gets clogged with dirt or grime or suffers any physical damage, it may fail to perform its function effectively.


The solution to the FTE problem is relatively straightforward. 

Regular cleaning and maintenance of the Beretta A400 Xtreme Plus is paramount to prevent the ejector from becoming dirty or clogged. 

Using a good quality gun solvent, clean the ejector and the surrounding areas thoroughly. If the ejector is damaged, it may need to be replaced. 

Always ensure that any replacements are done by a certified professional to maintain the integrity and safety of the firearm.

2 . Failure to Feed (FTF)


The Failure to Feed (FTF) issue with the Beretta A400 Xtreme Plus typically arises due to problems with the magazine tube or the ammunition itself. 

The magazine tube, designed to store and feed ammunition into the chamber, might have a defective spring or follower, or it could be obstructed by dirt or debris. 

As for the ammunition, it could be of poor quality or the wrong size, both of which can inhibit proper feeding.


The key to resolving the FTF problem lies in proper maintenance and use of appropriate ammunition

For issues with the magazine tube, ensure that it’s regularly cleaned to remove any dirt or obstructions.

 If the spring or follower is defective, replacement with an original Beretta part is recommended. 

As for ammunition, always use the recommended size and high-quality rounds. 

A consistent cleaning routine and the use of quality ammunition can significantly reduce the occurrence of this issue.

3 . Trigger Malfunction


The Trigger Malfunction in the Beretta A400 Xtreme Plus often arises due to excessive friction in the trigger assembly or a worn-out trigger spring. 

The trigger assembly consists of several intricate parts working in unison, and if they are not adequately lubricated, it can cause the trigger to become stiff or unresponsive. 

Similarly, a worn-out trigger spring can also lead to trigger malfunctions as it is unable to provide the required tension for proper operation.


The remedy for the Trigger Malfunction issue predominantly lies in proper lubrication and timely replacement of worn-out parts.

 Keeping the trigger assembly clean and well-lubricated can greatly reduce friction and ensure smooth operation. 

The use of high-quality gun oil for lubrication is strongly recommended. If the problem stems from a worn-out trigger spring, then it should be replaced immediately.

 Replace worn-out parts with original Beretta components to maintain the firearm’s performance and longevity.

4 . Misfires


Misfires in the Beretta A400 Xtreme Plus usually occur due to issues with the firing pin or the ammunition. 

The firing pin, responsible for striking the primer of the cartridge to ignite the gunpowder, can become faulty due to wear and tear or inadequate lubrication. 

On the other hand, the ammunition can be problematic if it’s of inferior quality or stored improperly, leading to damp or corroded rounds.


The solution to Misfires largely involves proper maintenance of the firing pin and careful selection and storage of ammunition

Regular cleaning and lubrication of the firing pin are crucial to prevent malfunction. If the firing pin shows signs of wear or damage, replacement is necessary. 

Always use high-quality ammunition and store it in a dry, cool place to prevent dampness or corrosion. These measures can greatly reduce the occurrence of misfires in your Beretta A400 Xtreme Plus.

5 . Sticky Safety


A Sticky Safety issue in the Beretta A400 Xtreme Plus is typically due to a buildup of dirt or grime in the safety mechanism or a lack of lubrication. 

Safety, an essential component of any firearm, prevents accidental discharges.

 Over time, dirt and debris can accumulate in this mechanism, causing the safety to become difficult to engage or disengage. 

Alternatively, inadequate lubrication can also lead to increased friction, resulting in a sticky safety.


Addressing the Sticky Safety issue primarily involves regular cleaning and appropriate lubrication of the safety mechanism.

 By making sure the safety mechanism is regularly cleaned, you can prevent dirt and grime from affecting its operation.

 Adequate lubrication with high-quality gun oil can also reduce friction, ensuring smoother engagement and disengagement of the safety. 

6 . Over-Pressure Signs


Over-pressure signs in the Beretta A400 Xtreme Plus typically surface due to using overcharged ammunition or a blockage in the barrel. 

Overcharged ammunition generates excessive pressure upon firing, which can strain and potentially damage the firearm’s components. 

Similarly, an obstruction in the barrel, such as mud or debris, can cause a dangerous pressure spike when the gun is fired.


To address overpressure signs, it’s crucial to always use standard factory-loaded ammunition and inspect the barrel for obstructions before use

If over-pressure signs are detected, immediately cease using the firearm and consult with a firearms professional. 

Never attempt to disassemble or repair a firearm showing signs of overpressure yourself

This can be dangerous and could potentially cause irreversible damage to the firearm. 

7 . Erratic Ejection Patterns


The Erratic Ejection Patterns in the Beretta A400 Xtreme Plus generally stem from issues with the ejection system – either a worn-out or damaged ejector or a weak or broken ejector spring. 

These components play a key role in expelling used cartridges, and if they are not functioning properly, it can result in unpredictable ejection patterns, impacting both safety and shooting accuracy.


Addressing Erratic Ejection Patterns involves careful inspection and possible replacement of the ejector and the ejector spring. 

Regular inspection of these parts for signs of wear or damage is crucial

If an issue is found, it’s advised to replace the faulty part immediately with an original Beretta component to maintain the firearm’s performance. 

Furthermore, keeping the ejection system clean and well-lubricated can help prevent such problems

As always, if you are unsure about the repair process, it’s best to seek professional assistance.

8 . Gas System Leakage


Gas System Leakage in the Beretta A400 Xtreme Plus typically arises due to a faulty gas valve seal or an ill-fitted, worn-out gas cylinder.

 The gas system, a fundamental component in semi-automatic shotguns, utilizes the energy from the ignited gunpowder to eject the spent shell and load a new one. 

If the gas valve seal is compromised or the gas cylinder is not fitting properly, it can lead to leakage, significantly affecting the gun’s performance and reliability.


To address Gas System Leakage, it’s vital to inspect and replace the gas valve seal regularly and ensure the gas cylinder fits properly. 

A faulty seal should be replaced immediately with an original Beretta part to prevent further damage. 

Similarly, if the gas cylinder is showing signs of wear or is not fitting correctly, it should be replaced.

9 . Inconsistent Cycling


The issue of Inconsistent Cycling in the Beretta A400 Xtreme Plus is typically a result of a poorly maintained or damaged gas system. 

The gas system, pivotal to the semi-automatic operation of the shotgun, can falter in its function if dirt or grime accumulates or if components like the gas piston or gas cylinder are worn out or damaged. 

This can lead to erratic cycling of shells, impacting the firearm’s performance.


To troubleshoot Inconsistent Cycling, regular and thorough cleaning of the gas system is crucial.

 Keeping the gas system clean and free from grime or debris can ensure smooth operation. 

Additionally, inspect the gas piston and gas cylinder for any signs of wear or damage. If any are found, replace them promptly with original Beretta parts to restore the firearm’s efficiency. 

As with all firearm maintenance, if you encounter difficulties or uncertainties, it’s advisable to consult a professional to avoid potential damage or safety risks.

10 . Defective Recoil System


The Defective Recoil System in the Beretta A400 Xtreme Plus is typically a consequence of a worn-out recoil spring or a broken recoil pad. 

The recoil system serves a crucial role in absorbing the shock generated during firing and ensuring smooth cycling of ammunition. 

If the recoil spring loses its strength or the recoil pad breaks, it can lead to a harsh recoil experience and potentially interrupt the firearm’s operation.


To rectify a Defective Recoil System, it’s integral to regularly inspect the recoil spring and recoil pad for any signs of wear, tear, or damage. 

If the recoil spring appears weak or the recoil pad is broken, it’s advisable to replace it immediately with original Beretta components to ensure optimal performance. 

Furthermore, regular cleaning and appropriate maintenance of the recoil system can prolong the lifespan of these components. 

11 . Barrel Leading


Barrel Leading in the Beretta A400 Xtreme Plus can typically occur due to repeated use of lead bullets, which can leave a residue or build-up of lead in the barrel. 

Over time, this accumulation can affect the firearm’s accuracy and overall performance. 

Additionally, high-velocity shooting and the use of softer lead bullets can exacerbate this situation.


To combat Barrel Leading, a routine and thorough cleaning process is a must. 

This involves using a quality bore cleaner and a bronze brush designed for your particular caliber to scrub out lead deposits. 

Furthermore, limiting high-velocity shooting and opting for harder lead bullets can help prevent excessive lead accumulation. 

It’s always recommended to seek professional advice if lead build-up is substantial or if you’re unsure about the cleaning process. Remember, a clean firearm is a well-functioning firearm.

12 . Difficulty in Disassembly and Reassembly


The Difficulty in Disassembly and Reassembly of the Beretta A400 Xtreme Plus can largely be attributed to the intricate design of the firearm and lack of familiarity with its components. 

Complex semi-automatic shotguns like the A400 Xtreme Plus require careful handling during disassembly to prevent damage or loss of internal parts. 

Moreover, the reassembly process can be challenging if the user is not well-acquainted with the specific sequence and arrangement of components.


To tackle the Difficulty in Disassembly and Reassembly, it’s recommended to familiarize oneself with the firearm’s manual and its detailed instructions.

 This can provide a deeper understanding of the weapon’s components and their specific placement, facilitating smoother disassembly and reassembly. 

Using the right tools meant for firearm maintenance can also make the process easier and prevent damage to the parts. 

Most importantly, practice and patience are vital during both disassembly and reassembly.


In conclusion, while the Beretta A400 Xtreme Plus is a high-performance firearm, like any mechanical device, it may encounter issues over time.

 Problems such as gas system leakage, inconsistent cycling, defective recoil system, barrel leading, and difficulty in disassembly and reassembly, if not addressed promptly, can affect the firearm’s performance and reliability. 

However, with regular maintenance, proper cleaning, and replacement of worn or damaged parts with original Beretta components, these issues can be kept at bay. 

Familiarizing oneself with the firearm’s manual, using the right tools, and seeking professional assistance when in doubt can significantly simplify the maintenance process. 

Remember, a clean, well-maintained firearm is not only more reliable and efficient but also ensures the safety of the user.


What can I do to prevent inconsistent cycling in my Beretta A400 Xtreme Plus?

Regular cleaning of the gas system and replacing worn-out parts with original Beretta parts can prevent inconsistent cycling.

My Beretta A400 Xtreme Plus has a harsh recoil, how can I rectify this?

Check the recoil spring and recoil pad for signs of wear or damage. Replace them with original Beretta components if necessary.

What causes barrel leading in the Beretta A400 Xtreme Plus?

Repeated use of lead bullets, especially softer ones, can cause barrel leading. Regular cleaning and using harder lead bullets can help prevent this.

I’m having difficulty disassembling and reassembling my Beretta A400 Xtreme Plus, what should I do?

Familiarize yourself with the firearm’s manual and use the right tools. Practice and patience are essential, but if it feels too complex, seek professional help.

Beretta 1301 Problems

Beretta 694 Problems

Beretta 84 Problems

Beretta A400 Xplor Problems

Beretta A300 Outlander Problems

Beretta CX4 Storm Problems

Beretta DT11 Problems

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top